Definity ECS и Cisco 5200 ISDN PRI E1 ETSI

Тема:

Ваше сообщение:
> Добрый день! > Помогите, плз: > Имеем станцию Definity ECS > и Cisco 5200 > Задача включить киску по ISDN PRI E1 etsi(net5) > и организовать простой модемный пул терминирующий > аналоговые звонки. > При использовании приведенных ниже конфигураций не > встает 2 уровень. В конце приведен дебаг с киски. > Спасибо > > DEFINITY CONFIG > --------------- > DS1 > ------------------------- > Bit Rate: 2048 > Line Coding: hdb3 > Sig Mode: isdn-pri > Connect: Network > Interface: Network > Country Protocol: etsi > Protocol Version: a > Interfaсe Compand: alaw > CRC?: y > IdleCode: 01010100 > DCP/Analog: 3,1 kHz > ------------------------- > Signaling Group > ------------------------- > Associated Signal: Y > Primary D-Channel: 1B0516 > Trunk Group: 10 > Supplementary Service Protocol: a > Max Numb of NCA TSC: 0 > Max Numb of CA TSC: 0 > Trunk Group for NCATSC: 10 > ------------------------- > Trunk Group 10 > ------------------------- > Direction: two-way > Service Type: public-ntwrk > Digit Handling (in/out): overlap/overlap > Trunk Hunt: descend > остальное по умолчанию > ___________________________________________________________________________________ > CISCO CONFIG > ------------ > isdn switch-type primary-net5 > controller e1 0 > framing crc4 > linecode hdb3 > pri-group > interface Serial0:15 > ip address 10.20.30.1 255.0.0.0 > no ip directed-broadcast > encapsulation ppp > no keepalive > isdn switch-type primary-net5 > isdn incoming-voice modem > ppp authentication chap > ! > _____________________________________________________________________________________ > CISCO DEBUG > ------------ > debug isdn events > debug isdn q931 > debug isdn q921 > > 7w0d: %CONTROLLER-5-UPDOWN: Controller E1 0, changed state to up > 7w0d: %CSM-5-PRI: add PRI at slot 0, unit 0, channel 15 with index 0 > 7w0d: %LINK-3-UPDOWN: Interface Serial0:15, changed state to up > 7w0d: in Pri_Activate_L2 for dsl 0 > 7w0d: ISDN Se0:15: Activating > 7w0d: ISDN Se0:15: Could not bring up interface > 7w0d: ISDN Se0:15: L1 is IF_ACTIVE > 7w0d: in Pri_Activate_L2 for dsl 0 > 7w0d: ISDN Se0:15: L1 ERR IF_ACTIVE > 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0 > 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0 > 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0 > 7w0d: ISDN Se0:15: L1 ERR IF_ACTIVE > 7w0d: ISDN Se0:15: L1 ERR IF_ACTIVE > 7w0d: %ISDN-6-LAYER2DOWN: Layer 2 for Interface Se0:15, TEI 0 changed to down > 7w0d: ISDN Se0:15: Event: received NL_REL_IND > 7w0d: %CSM-5-PRI: delete PRI at slot 0, unit 0, channel 15 with index 32 > 7w0d: %CONTROLLER-5-UPDOWN: Controller E1 0, changed state to administratively down > 7w0d: ISDN Se0:15: Physical layer is IF_DOWN > 7w0d: ISDN Se0:15: Shutting down ME > 7w0d: ISDN Se0:15: Shutting down ISDN Layer 3 > 7w0d: ISDN Se0:15: Event: received MNL_RESET_REQ > 7w0d: %LINK-5-CHANGED: Interface Serial0:15, changed state to reset > 7w0d: %CONTROLLER-5-UPDOWN: Controller E1 0, changed state to up > 7w0d: %CSM-5-PRI: add PRI at slot 0, unit 0, channel 15 with index 0 > 7w0d: ISDN Se0:15: L1 is IF_ACTIVE > 7w0d: in Pri_Activate_L2 for dsl 0 > 7w0d: ISDN Se0:15: L1 ERR IF_ACTIVE > 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0 > 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0 > 7w0d: %LINK-3-UPDOWN: Interface Serial0:15, changed state to up > 7w0d: in Pri_Activate_L2 for dsl 0 > 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0 > 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0 > 7w0d: %ISDN-6-LAYER2DOWN: Layer 2 for Interface Se0:15, TEI 0 changed to down > 7w0d: ISDN Se0:15: Event: received NL_REL_IND > 7w0d: %CONTROLLER-5-UPDOWN: Controller E1 0, changed state to down > 7w0d: %CSM-5-PRI: delete PRI at slot 0, unit 0, channel 15 with index 32 > 7w0d: ISDN Se0:15: Physical layer is IF_DOWN > 7w0d: ISDN Se0:15: Shutting down ME > 7w0d: ISDN Se0:15: Shutting down ISDN Layer 3 > 7w0d: ISDN Se0:15: Event: received MNL_RESET_REQ > 7w0d: %LINK-5-CHANGED: Interface Serial0:15, changed state to reset > 7w0d: %CONTROLLER-5-UPDOWN: Controller E1 0, changed state to up > 7w0d: %CSM-5-PRI: add PRI at slot 0, unit 0, channel 15 with index 0 > 7w0d: ISDN Se0:15: L1 is IF_ACTIVE > 7w0d: in Pri_Activate_L2 for dsl 0 > 7w0d: ISDN Se0:15: L1 ERR IF_ACTIVE > 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0 > 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0 > 7w0d: %LINK-3-UPDOWN: Interface Serial0:15, changed state to up > 7w0d: in Pri_Activate_L2 for dsl 0 > 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0 > 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0 > 7w0d: %ISDN-6-LAYER2DOWN: Layer 2 for Interface Se0:15, TEI 0 changed to down > 7w0d: ISDN Se0:15: Event: received NL_REL_IND > _________________________________________________________________________________________

Optional Link URL:
Link Title:
Optional Image URL: