Re: Definity ECS и Cisco 5200 ISDN PRI E1 ETSI
Отправлено: Игорь Зафиевский on February 29, 2000 at 18:54:19:
В ответ на: Definity ECS и Cisco 5200 ISDN PRI E1 ETSI posted by Денис Евладов on February 29, 2000 at 16:46:00:
Привет! > Добрый день!
> Помогите, плз: > Имеем станцию Definity ECS
> и Cisco 5200 > Задача включить киску по ISDN PRI E1 etsi(net5)
> и организовать простой модемный пул терминирующий
> аналоговые звонки. > При использовании приведенных ниже конфигураций не
> встает 2 уровень. В конце приведен дебаг с киски. > Спасибо >
> DEFINITY CONFIG
> ---------------
> DS1
> -------------------------
> Bit Rate: 2048
> Line Coding: hdb3
> Sig Mode: isdn-pri
> Connect: Network
> Interface: Network line-side, а не network > Country Protocol: etsi
> Protocol Version: a
> Interfaсe Compand: alaw
> CRC?: y
> IdleCode: 01010100
> DCP/Analog: 3,1 kHz
> -------------------------
> Signaling Group
> -------------------------
> Associated Signal: Y
> Primary D-Channel: 1B0516
> Trunk Group: 10
> Supplementary Service Protocol: a
> Max Numb of NCA TSC: 0
> Max Numb of CA TSC: 0
> Trunk Group for NCATSC: 10
> -------------------------
> Trunk Group 10
> -------------------------
> Direction: two-way
> Service Type: public-ntwrk
> Digit Handling (in/out): overlap/overlap Я бы здесь оставил enbloc/enbloc и кой-чего добавил в конфиге AS (см ниже). > Trunk Hunt: descend > остальное по умолчанию
> ___________________________________________________________________________________
> CISCO CONFIG
> ------------
> isdn switch-type primary-net5 > controller e1 0
> framing crc4
> linecode hdb3
> pri-group > interface Serial0:15
> ip address 10.20.30.1 255.0.0.0
> no ip directed-broadcast
> encapsulation ppp
> no keepalive
> isdn switch-type primary-net5
> isdn incoming-voice modem
isdn send-alerting
isdn sending-complete
isdn disconnect-cause not-available
> ppp authentication chap
> ! > _____________________________________________________________________________________
> CISCO DEBUG
> ------------
> debug isdn events
> debug isdn q931
> debug isdn q921
>
> 7w0d: %CONTROLLER-5-UPDOWN: Controller E1 0, changed state to up
> 7w0d: %CSM-5-PRI: add PRI at slot 0, unit 0, channel 15 with index 0
> 7w0d: %LINK-3-UPDOWN: Interface Serial0:15, changed state to up
> 7w0d: in Pri_Activate_L2 for dsl 0
> 7w0d: ISDN Se0:15: Activating
> 7w0d: ISDN Se0:15: Could not bring up interface
> 7w0d: ISDN Se0:15: L1 is IF_ACTIVE
> 7w0d: in Pri_Activate_L2 for dsl 0
> 7w0d: ISDN Se0:15: L1 ERR IF_ACTIVE
> 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0
> 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0
> 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0
> 7w0d: ISDN Se0:15: L1 ERR IF_ACTIVE
> 7w0d: ISDN Se0:15: L1 ERR IF_ACTIVE
> 7w0d: %ISDN-6-LAYER2DOWN: Layer 2 for Interface Se0:15, TEI 0 changed to down
> 7w0d: ISDN Se0:15: Event: received NL_REL_IND > 7w0d: %CSM-5-PRI: delete PRI at slot 0, unit 0, channel 15 with index 32
> 7w0d: %CONTROLLER-5-UPDOWN: Controller E1 0, changed state to administratively down
> 7w0d: ISDN Se0:15: Physical layer is IF_DOWN
> 7w0d: ISDN Se0:15: Shutting down ME
> 7w0d: ISDN Se0:15: Shutting down ISDN Layer 3
> 7w0d: ISDN Se0:15: Event: received MNL_RESET_REQ
> 7w0d: %LINK-5-CHANGED: Interface Serial0:15, changed state to reset > 7w0d: %CONTROLLER-5-UPDOWN: Controller E1 0, changed state to up
> 7w0d: %CSM-5-PRI: add PRI at slot 0, unit 0, channel 15 with index 0
> 7w0d: ISDN Se0:15: L1 is IF_ACTIVE
> 7w0d: in Pri_Activate_L2 for dsl 0
> 7w0d: ISDN Se0:15: L1 ERR IF_ACTIVE
> 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0
> 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0
> 7w0d: %LINK-3-UPDOWN: Interface Serial0:15, changed state to up
> 7w0d: in Pri_Activate_L2 for dsl 0
> 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0
> 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0
> 7w0d: %ISDN-6-LAYER2DOWN: Layer 2 for Interface Se0:15, TEI 0 changed to down
> 7w0d: ISDN Se0:15: Event: received NL_REL_IND > 7w0d: %CONTROLLER-5-UPDOWN: Controller E1 0, changed state to down
> 7w0d: %CSM-5-PRI: delete PRI at slot 0, unit 0, channel 15 with index 32
> 7w0d: ISDN Se0:15: Physical layer is IF_DOWN
> 7w0d: ISDN Se0:15: Shutting down ME
> 7w0d: ISDN Se0:15: Shutting down ISDN Layer 3
> 7w0d: ISDN Se0:15: Event: received MNL_RESET_REQ
> 7w0d: %LINK-5-CHANGED: Interface Serial0:15, changed state to reset > 7w0d: %CONTROLLER-5-UPDOWN: Controller E1 0, changed state to up
> 7w0d: %CSM-5-PRI: add PRI at slot 0, unit 0, channel 15 with index 0
> 7w0d: ISDN Se0:15: L1 is IF_ACTIVE
> 7w0d: in Pri_Activate_L2 for dsl 0
> 7w0d: ISDN Se0:15: L1 ERR IF_ACTIVE
> 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0
> 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0
> 7w0d: %LINK-3-UPDOWN: Interface Serial0:15, changed state to up
> 7w0d: in Pri_Activate_L2 for dsl 0
> 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0
> 7w0d: ISDN Se0:15: TX -> SABMEp sapi = 0 tei = 0
> 7w0d: %ISDN-6-LAYER2DOWN: Layer 2 for Interface Se0:15, TEI 0 changed to down
> 7w0d: ISDN Se0:15: Event: received NL_REL_IND
> _________________________________________________________________________________________
Отклики:
Написать ответ
| 
